DISCLOSURE: This post may contain affiliate links, meaning when you click the links and make a purchase, we receive a commission at no additional cost to you
A washing machine can easily have one error code. One error code would be easy to figure out. However, two codes popping up on your Maytag washer display may be more problematic if you’ve never seen them before.
The Maytag washer error code F03 E01 means two things. The main problem is your washer’s control board can’t sense the water level. This could be because of a bad pressure sensor, wiring, a bad control board, or a clogged air pipe. The other code tells you the door is locked.
A locked door on a washer is typical when the machine suddenly stops because the door is set to remain locked until all water is drained. If the machine stops in mid-cycle, the door won’t open.The main problem remains the water level issue and that is where you must look.
What Should I Do First?
The likely culprit is either the pressure switch hose or the air trap tube. The pressure switch hose can give you some trouble since it can get clogged with dirty water and yucky deposits
You should check the pressure sensor first since it is the most common problem with this error.
Connect with an Appliance Repair Tech
Click here to use the chatbox to speak with one of our technicians.
No in-home service calls. No appointments.
A pressure sensor messages the control board the water is at the right level. It also messages to start draining and also keeps the heating element from overheating.
You want to check the water level pressure hose first. It’s found between the pressure switch and the air trap. It can get pinched and twisted which can cause the F03 E01 error.
Move the hose around to ensure is it placed correctly and to see if it has any damage. You will want to disconnect it from the pressure switch and blow it out to check for blockages. Foam and water can be trapped inside too.
Put everything back together and start a cycle. A normal operation shows the problem was solved.
Replace the pressure hose if the error shows up again.
Inspect the Pressure Sensor
You will also want to look at the pressure sensor. It is found on the right side of the top rear of the case in most Maytag models. You may need to look at your owner’s manual to be sure. The sensor is round and has a nozzle and a thin hose connected to it.
In some models, you may need to remove the back cover of the machine to get to the sensor.
Connect with an Appliance Repair Tech
Click here to use the chatbox to speak with one of our technicians.
No in-home service calls. No appointments.
Once you find it, you will need to check it with a voltmeter. Attach the black probe to the PS8 board connector, pin 8 (GND), and the red one to PS8, pin 4. The sensor should be replaced if there is no voltage or really low voltage.
The good news is a new sensor is super cheap. It only costs between $20 ad $30.
While you are looking at the sensor, make sure it is fully encased in the center unit. Also, see that the pressure sensor harness is securely attached. Fixing a loose-fitting sensor or harness could solve your problem.
The Air Trap Pipe
Grime and deposits can make their way into the air trap pipe. This is a pipe that is under the drain grate. It can have soap and moisture in it that triggers the error code.
The pipe is meant for airflow so it can press on the pressure switch. When it becomes clogged, it detects the wrong water level in the drum and sends the wrong signal to the control board.
You will need to be careful about unclogging the air trap pipe. You can use a tool called a “snake”, which is a cable that unclogs pipes. You may be able to use a rag with a cleaning solution on it on a short pole to clean the inside of the pipe.
Another option is a slim, round, scrub brush that can go up in the pipe and whish away the scum.
Check the Wiring
Wiring can become damaged when a washing machine is constantly vibrating. Chronic overloading, causing excessive movement, can also damage wiring. In this can, the error code will appear, then disappear indefinitely. It can reappear periodically.
You need to check the wiring with a multimeter. Visually look at it to see if there are some stripped, twisted, or broken ends. Finding damaged wiring means you will need to call your service technician to replace them.
Related: Here Is Why Washing Machine Shaking Too Much During Spin Cycle?
Consider Your Control Unit
Assuming everything else is working properly, the last thing that could be wrong is your control unit is faulty. You can know this is probably the root problem when the error comes on immediately after turning on the machine or when the washer begins its cycle.
You will need to call your service technician to replace a control board issue. The cost will be around $270 but could vary, depending on your service technician’s pricing.
Related: 5 Reasons Why Maytag Washer Is Not Turning On
FAQs
How do I clear an error code on my Maytag washer?
Once you fix the problem, you can remove a code by pressing the pause or cancel button two times and then pressing the power button once. If the code remains, unplug the washer for a minute. Remove any items from the wash and restart the washer on a clean washer cycle.
How can I reset my Maytag washer?
There are a couple of ways to reset your washer to a different cycle and clear the codes.
The first way is to press the power/cancel button, then pick a wash cycle, and then press the start-pause button.
The second way is to unplug it from the wall, wait a solid minute and plug it back into the wall outlet. You should see the codes are gone from your washer’s display.
How can I get into the diagnostic mode on my Maytag washer?
For the test, the washer needs to be on and in standby mode. That means it must be connected to power with all indicator lights off.
Press a button, any button except start, power, or stop, and hold for three seconds. Release and then do it again for three seconds. Do this a third time with the same button.
Indicator lights will flash and go off after five seconds. You will see an “88” on the display. You may also see fault codes show up. Write those down for your service technician or to research later.
If there are no errors, the lights will flash again and the “88″ will show. The machine will then go into test mode automatically within five seconds. You do nothing until the test is complete. Then press the power or stop button to get out of the program.
Can I drain my Maytag washer manually?
You can drain your Maytag washer manually. You will need a bucket and a pitcher.
Turn the power and water to the machine off. You will need to move the washer to get to the back of it.If the washer door isn’t locked, take out your laundry and scoop out as much water as you can. If it’s locked because water is in the drum, you will need to drain it all from the back.
To drain it from the back, take the drain hose out of the drain and put it in the bucket. The water will automatically drain. Once all the water is drained, the door should open. However, you may need to reset the washer to get the door lock to open.
Related: How To Effectively Clean Washing Machine?
Conclusion
While this error could signal that there are several things wrong with your Maytag washer, the two most common things are clogged hoses or the pressure sensor. Any of those can be fixed as a DIY project in just a couple of hours at most, even by someone inexperienced. They are cheap, easy fixes that can be done quickly to get your washer back up and running.
Read: Why Maytag Washer Door Locked Flashing? Troubleshooting Guide
FAQs
What does E01 and F03 mean on a Maytag washer? ›
The F3 E1 alert indicates the washer can't detect the water level. There may be an issue with the appliance control unit or associated wiring. Shut off water valves to the washer, and call for service.
How do I fix my F3 E1 Maytag washer? ›- Power unit down by turning off the circuit breaker or unplugging for one (1) minute.
- Power unit up by reconnecting power.
- Restart a new cycle.
- Monitor the washer for one (1) minute to ensure the error code does not display again.
"F03" displayed on screen The washer is not emptied. The washer stops the program being executed. Shut down the machine and disconnect power supply. Check: • Drain pipe is knotted or not.
How do I reset my Maytag error? ›The easiest way to reset a Maytag washer is to disconnect the power to the washing machine for three minutes. Disconnecting the power allows the electrical charge to dissipate from the washing machine, which allows it to reset. If the reset fails, unplug the washer again, this time leaving it unplugged for ten minutes.
What does error code E3 F3 mean on Maytag? ›There may be a problem with the Oven Temperature Sensor, the Control, or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven for one (1) minute to ensure the error code does not display again.
Can you reset a washer by unplugging it? ›Reset your washing machine
What you can do instead is power cycle it: Unplug it (or turn off power at the circuit breaker), wait some time for the electrical charge to clear out of the washer (usually 1 to 5 minutes at most), and then power it up again. This is the closest you can get to a "reset" of the washer.
| Display | Meaning | Possible causes |
|---|---|---|
| F03 | Following error message of the position controller (in OPMODE 5 or 6 only) | Amplifications set too low. Axis is too undynamic |
| Amplifications set too high. Axis oscillates. | ||
| IPEAK (maximum current) too low |
Before commencing the wash cycle, pour 4 lbs of water over the clothes and let water to soak into the fabric. Start the wash cycle. The machine will think the load is 6 lbs instead of 2 lbs and it will fill water for 6 lbs cloth loads automatically. You have successfully bypassed water level sensor.
How do you know if your washing machine transmission is bad? ›If your transmission is broken, the water may drain, but the spin cycle may fail to start. The spin cycle removes as much water from the clothes as possible so your dryer doesn't have to work overtime to dry your clothes (something that can lead to dryer issues, by the way).
Why is my Maytag washer not spinning and draining? ›Make sure that the drain hose is not kinked or clogged. Straighten the hose for adequate water flow. Remove any blockage from the drain hose, drainpipe or utility sink. Use the U-shaped drain hose form on the drain hose, and secure the drain hose.
What are common problems with Maytag washers? ›
- Washer Making Loud Noise When Spinning. Maytag washer problems can begin with some loud noises. ...
- Washer Won't Spin At All. ...
- Washer Door Won't Lock. ...
- Dryer Takes Two Cycles to Dry Clothes. ...
- Dryer Won't Start. ...
- Dryer Drum Not Turning.
The "Err" message will appear under the following situations: You attempt to change or modify the cycle while the washer is running.
What is the clean code on Maytag washer? ›The CL code is a reminder to run the Clean Washer cycle and will appear after 30 cycles. The code will automatically clear once a Clean Washer cycle has completed or after three cycles.
What does f3 e2 mean on Maytag? ›F3E2 - Moisture Sensor
The F3E2 error code occurs when five consecutive loads are dried without registering moisture sensor data. Pressing the 'Power' button will clear the error code and allow you to restart the machine. If the problem persists, call for service.
Did you receive a F0 E3 oversized load alert? If F0 E3 appears, the load is too large. If an overload is detected, the washer will drain any water and detergent in the washer. Remove several items and add HE detergent.
What does f3 e2 mean washing machine? ›The F3E2 Error Code indicates that there may be an issue with the Temperature Control sensor. Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute, and then plugging it back in. If unsuccessful, call for service.
How long to leave washer unplugged to reset? ›To reset the electronic controls on your washer, shut off the circuit breaker or fuse to the washer or unplug the washer for 2 minutes. For models that have a timer control knob, turn the knob around and back to any position other than final spin for the interrupted cycle. Then, restore power.
What is a master reset on a washing machine? ›If you see no change, you can try a Master Reset. This will reset all of the onboard componentry and is often successfully used by appliance technicians. Open and close the door of the washing machine 6 times within 12 seconds. Then, run the rinse/spin cycle without clothing to see if your problems are resolved.
Will unplugging Maytag washer reset it? ›Disconnect the Power
Disconnecting the washer's electricity for three minutes is the simplest way to reset a Maytag washing machine. When the power is cut off, the washing machine's electrical charge can dissipate, allowing it to reset. If the reset doesn't work, unplug the washer once more, this time for ten minutes.
Unplug your washer for about one minute. Then, plug the appliance back in. Open and close the door six times in 12 seconds to tell the computer to reset everything. This may not work on all machines, but it's an easy fix if yours is compatible with this technique.
Can you unplug a washing machine mid cycle? ›
In an emergency, simply pull the washing machine's plug to instantly disconnect the power supply. This will stop the washing machine immediately, although be aware that it may not drain the water away and this could spill out if you open the door.
How do you diagnose a broken washing machine? ›- Loud Banging Noises. While it can be common for your washing machine to become unbalanced during a washing load, this should not happen frequently. ...
- Won't Drain. ...
- Leaks. ...
- A Drum That Won't Budge. ...
- A Locked Door.
You can manually fill your top load washer for the wash cycle water if you have rain or other stored water. To do this following process: Remember that the machine uses half of the water during the wash cycle and half during the rinse cycle. You will therefore have to fill the machine twice.
Is it OK to put extra water in washing machine? ›Nope! Using additional water does not get your laundry any cleaner. The extra water dilutes the concentration of detergent. Plus it reduces the mechanical action of the clothes rubbing against one another, the tub, or the agitator, which helps remove dirt and stains.
How can I make my washing machine work better? ›Regular cleaning: Clean your washing machine on a regular basis is an effective way to avoid build up habitat and detergent residue in the washing drum. After washing, running an empty cycle with two cups of white vinegar will help you to improve the performance of your washer.
What is the pressure sensor error on a washing machine? ›A: The PE error code indicates that either the wiring that connects the water level pressure sensor is faulty, or the water level pressure sensor itself is faulty. To find out which one is the cause of the error code, it will need to be tested and if defective, replaced.
Where is the position of sensor in washing machine? ›In a washing machine, the Hall Effect sensor is mounted onto a printed circuit board in the electronics panel or onto the frame of the appliance, and a magnet is mounted on the rotating dial.
What are the three sensors used in washing machine? ›- Temperature.
- Rotor position sensor.
- Water level.
- Dirt sensor.
- Photoelectric sensor.
- Pressure sensor.
- Vibration sensor.
The average cost for a Washer Fluid Level Sensor Replacement is between $115 and $137. Labor costs are estimated between $76 and $96 while parts are priced between $39 and $41.
How do I fix E01 on my washing machine? ›- Switch off and unplug your machine.
- Check the door lock itself. (Sometimes the plug on the lock can melt.)
- Check the wiring to the door lock.
- Check the wiring to the control board from the door look.
How do you fix f3 E1 error on a Whirlpool washer? ›
The F3E1 Error Code indicates that there may be a problem with the Water Pressure sensor. Verify that your water supply has the adequate amount of pressure going to the washer/dryer. Try resetting the washer/dryer by unplugging it from the outlet for at least 1 minute and then plugging it back in.
How do you fix E01? ›The fluff filter of your dryer has become blocked with fabric softener residue (difficult to detect) or with fluff. Our advise is to clean the fluff filter after each drying cycle.
What does E1 mean on a Maytag washer? ›E1 Error code means the correct water level has not been reached within 20 minutes of the washer starts. Check the following: Check that the water faucets are not closed. Check that the water pressure in the house is over 20 kPa.
What does E01 and F03 mean? ›The error code F03/E01 indicates a problem with the water level. If your washer doesn't get enough water, it will not be able to work correctly. Most of the time, this error code is a result of a faulty sensor, hose, or brand pipe. Now that we know what the error code means, let's try to fix it.
What does error code f3 e0 mean on Whirlpool? ›There may be a problem with the Oven Temperature Sensor, the Control, or the associated wiring. Power unit down by turning off the circuit breaker(s) for one (1) minute. Power unit up by turning on the circuit breaker(s). Monitor the oven for one (1) minute to ensure the error code does not display again.
What is the error code e03 on a washing machine? ›Should the error code E3 appears it is warning that the machine is not draining. You can easily fix this problem by removing any blockages from the drain pump situated at the front of the machine for easy access. Should the error code E3 appears it is warning that the machine is not draining.
What does F 03 on a washing machine mean? ›F03 — Temperature sensing fault. Issue: Washing Machine is not heating on wash or dry settings. Advice: We recommend you call our customer service centre to book an engineer on: 0344 822 4224. F05 — Waste pipe blockage or pump issue.
What is the error code for drain problem on Whirlpool washer? ›F21 Error Code
F21 indicates a drain problem. Try the following method to resolve: Select PAUSE/CANCEL twice to cancel the cycle. Unplug washer or disconnect power.
Open the dispenser drawer by pulling on the handle at the base of the washer. This will reveal the drain pump filter. Remove the drawer by releasing the tab on each side. With your finger, push down on tab on right side of drawer, and up on tab on left side of drawer.
Why won t my Maytag washer drain or unlock? ›Drain Hose is Kinked or Clogged
A hose that's kinked or clogged by lint or debris causes a washing machine not to drain because water can't bypass the blockage. This often results in puddles in the washer drum or leaking. To remove any kinks, disconnect the hose clamp at the washer and gently straighten the hose.